Description

Products Description

product-1200-550

No Moving Parts, high accuracy for years long.

No moving components in the flow sensor, avoid long-term abrasion of mechanical parts which may result in inaccuracy measurement and failure of the meter.

Such design is also resistant to impurities, therefore no inspections and maintenance are cost-free.

Product features

Low starting rate (5L/h), able to accurately measure;
Flow rate as low as 12.5L/h;
Dynamic range (Q3/Q1) achieved 200:1;
No mechanical moving parts, no abrades, and has a long serving lifetime;
Small pressure loss
Can measure flow rate
High measurement frequency
Infrared photoelectric reading interface
Capacitive sensing touch
Battery ER26500 8500mAh
Material: 58 copper, ABS plastic
Mounting in any installation position;
Alarm when there is air;
Support RS485 modbus/ LoRa/LoRaWAN/NB-IOT; suitable for outdoor installation;
IP68 protection level
Data is not lost in the event of power failure. Data can be saved for more than 10 years and 23 months of historical data can be automatically saved;
Technical data conform to international standard ISO 4064.
ISO9001 certification
Warranty:2 years

outline dimension drawing

product-1200-342

Nominal Diameter	Length L	Length L1	Width B	High H	Connecting Thread
mm					d	D
15	165	260	95	86	R	G/B
20	195	300	95	86	R	G1/B
25	225	346	95	89	R1	G1/B
32	180	305	95	100	R1	G1/B
40	200	330	95	120	R1	G1/B

technical parameter

Nominal diameter (mm)	15	20	25	32	40
Overload flow Q4 (m/h)	3.125	5	7.875	12.5	20
Permanent flow Q3 (m3/h)	2.5	4	6.3	10	16
Transitional flow Q2(m3/h)	0.02	0.032	0.05	0.08	0.128
Minimum flow Q1 (m3/h)	0.0125	0.02	0.0315	0.05	0.08
Start-up flow (m3/h)	0.005	0.005	0.008	0.01	0.015
Max flow	999999.999
Measuring range	Q3/Q1, R200/(R250 customizable)
Accuracy class	Class 2
Pressure loss class	≤0.04 MPa
Working pressure	1.6 MPa
Temperature class	T30/T50
Temperature range	(5~55)℃
Storage temperature	-20~60℃
Environment class	Class B
Electromagnetic class	E1
Power supply	Built-In Lithium battery DC 3.6V
Battery life	8-10 years
Battery capacity	8500mAh
Power consumption	10μA
Installation position	Any angle
Display	LCD, 8 digits +additional characters
Installation pitch	U10/D5
Communication Interface	RS485 modbus/ LoRa/LoRaWAN/NB-IOT
Protection class	IP68

notices for installation

Flush pipes before installation to avoid gravel and other foreign objects
Install a valve and filter before the water meter;
Do not touch the electrical part or pull wires to avoid damage during installation;
When the water meter is installed in a horizontal or inclined way, the ultrasonic flow probe on pipes shall be placed horizontally, and when installed in a vertical way, make sure the water flows from down to up.
Please note that the arrow direction on the pipe shall be consistent with the water flow direction during installation;
The joint washer shall be installed correctly to avoid misaligned washer blocking water and affecting the accuracy of the water meter;
The water meter shall not be installed at a place that may be affected by strong mechanical vibrations; Special Notices:
Be sure to install an on-off valve and filter before the water meter and another on-off valve is recommended after it for maintenance.In order to prevent backflow, a check valve should be installed in front of or behind the water meter.

Before using this water meter, the pipe must be filled with water, otherwise it will lead to inaccurate or even non-measurement;
When installing the water meter, should be reserved length of DN*10 in front of the water meter. Or should be reserved the length of DN*5 behind the water meter;
The water meter shall refresh the display at every 4s, and read the water meter (including the starting value and end
value) 4s at least after the valve is closed when test the water meter, otherwise the testing results may be affected;
Please make sure the medium flow is within the flow range of the water meter during test and use, otherwise it may result in damage to the water meter;
In case of any malfunction (e.g. metering failed, etc.) during use, please contact the related management department
immediately and do not repair it by yourself;
The product is designed with a disposable anti-disassembly seal which shall be removed only by appointed personnel, or otherwise it shall be excluded from the free after-sales service.